|
OutBack FX Series
OutBack VFX Series
Mate System
Controller & Display
Outback Flexware Power Panels
OutBack
FX Series Sinewave Inverters
The OutBack
modular 'building block' sinewave inverter/chargers can be used for
both small and large power systems in both residential and commercial
applications.
Each Outback
inverter/charger module is a complete system - DC to AC inverter
battery charger and AC transfer switch. Additional
inverter/chargers can be connected at any time in either parallel (230
Vac) or three phase (230Y400 Vac) configurations, allowing the system
to be tailored to the specific power requirements of the application.
Up to ten
inverter/chargers can be connected together to provide up to 30kW of
continuous power using a HUB10 communications manager and MATE system
display. The FX series also features a programmable AUX relay
that can be used for generator start-up, alarms & more. Smooth
sinewave output, with high efficiency (92% max), high surge capability
& low idle current.
All units
feature:
30A automatic
AC transfer relay. Powder coated all aluminium die-cast chassis
for maximum heat dissipation. Conformal coated circuit boards to
resist corrosion. Designed to allow easy field servicing and
repair.
Specifications
-
Input Voltage:
11.8-16.5; 22-33 VDC
-
Output Voltage: 230 Vac
(+/- 5%)
-
Output Frequency: 50Hz (+/-
0.04%) Sinewave
-
Power draw in search mode:
less than
0.5W
-
Power draw in on mode (idle):
20W typical
-
Load
sensing: Programmable down to 1W
-
Max. Efficiency:
93%
-
Warranty: Two years
OutBack
FX Series
 The OutBack FX
series inverter/chargers are designed to survive harsh environments
anywhere in the world. Their unique sealed, gasketed die-cast
aluminium chassis protects the electronics against dust, corrosion,
animals & insects. The FX series can be used is high ambient
temperature applications up to 60 deg. C with reduced output
ratings. All Programmed setpoints are stored in permanent
(NOV-RAM) memory to eliminate the need to re-programme the system
after a shutdown or battery replacement.
up to
the top
OutBack
VFX Series
 The Outback VFX
series (vented) is designed for use in more protected
environments. A cooling fan circulates outside air through the
inverter/charger to allow higher continuous power capacity. A
removable, washable intake filter is included with all VFX models.
| Model Number |
Continuous
Rating |
Surge Rating
RMS 100m/sec |
DC Voltage
Input |
Max Charge
Rate |
Data Sheet |
| FX2012ET |
2000 W |
4600 W |
12 V |
100 A |
FX & VFX Data Sheet |
| FX2024E |
2300 W |
5750 W |
24 V |
55 A |
| FX2348E |
2300 W |
5750 W |
48 V |
35 A |
| VFX 2612E |
2600 W |
4600 W |
12 V |
125 A |
| VFX 3024E |
3000 W |
5750 W |
24V |
85 A |
| VFX 3048E |
3000 W |
5750 W |
48 V |
45 A |
MATE
System Controller & Display
Complete
system controller for both FX inverters and MX60 PV charge
controller. Provides display of operation, allows control and
adjustments of set points, and co-ordinates the operation of entire
system to maximise performance. A single MATE can communicate
with 4 OutBack products using the HUB-4 or 10 using the
HUB-10. Can be mounted up to 300m away.
Includes 4-line
LCD display, 15m cable & clock to enable programming of the
inverter operation based upon time of day and day of week.
RS-232 port for connection of a PC.
Data Sheet
|
FX-MATE |
System controller & display (surface
mount) |
|
FX-MATE2 |
System controller & display (panel
mount) |
|
FX-HUB4 |
4 inputs/1 MATE communication
manager |
|
FX-HUB10 |
10 inputs/ 1MATE communication
manager |
|
FX-DCA |
DC conduit adaptor |
|
FX-ACA |
AC conduit adaptor |
|
FX-RTS |
Remote temperature sensor (6m cable) |
OutBack
Flexware Power Panels
OutBack
FLEXware offers savings in time, money and space by combining the
disconnects, overcurrent protection devices, earthing and control
components needed as part of a renewable energy system into easy to
install enclosures.
FLEXware Guide
 OutBack
FLEXware FX-250
For one FX
Series inverter/charger, AC & DC circuit breakers. (shunt breakers &
bypass not included - See below.)
OutBack FLEXware FX-500
For one or
two FX Series inverter/chargers, up to three MX60
charge controllers, a MATE system controller, a
HUB, AC & DC
circuit breakers and disconnects.
OutBack
FLEXware FX-1000
Expandable
system for up to four FX series inverter/chargers, up to four MX60
charge controllers, a MATE system controller, a HUB, AC & DC circuit
breakers and disconnects.
Each FX-500
or FX-1000 system consists of:
Mounting
plate
Fits 2
inverters. Supplied with mounting hardware. One needed for FLEXware 500;
two for FLEXware 1000.
D C
enclosures
Includes
knockouts for conduits and breakers, negative & positive bus-bars,
500/1000A 50mV DC current shunt. Requires DC circuit breakers.
AC enclosure
Includes
Earth & neutral bus-bars, conduit knockouts, and knockouts for
additional breakers. FLEXware 1000 offers version for use in three
phase
systems.
Input/Output
Bypass Assemblies
Includes dual
input/output bypass assembly, and AC breakers.
(FX-250: 3 x
30A; FX-500: 6 x 30A; FX-1000: 12 x 30A or 9 x 30A for three phase unit)
|
OB-FW250 |
FLEXware 250 DC &/or AC enclosure |
|
OB-FW-IOB-S-230VAC |
FLEXware 250 AC 30A Input/Output Bypass |
|
OB-FWMP |
FLEXware mounting plate |
|
OB-FW500DC |
FLEXware 500 DC enclosure |
|
OB-FW500AC |
FLEXware 500 AC enclosure |
|
OB-FW1000DC |
FLEXware 1000 DC enclosure |
|
OB-FW1000AC |
FLEXware 1000 AC enclosure |
|
OB-FW-IOB-D-230VAC |
FLEXware 500 AC 60A Input/Output Bypass |
|
OB-FW-IOB-Q-230VAC |
FLEXware 1000 AC 120A Input/Output Bypass |
|
OB-FW-IOB-Q-230/400VAC |
FLEXware 1000 AC 30A 3 Phase Input/Output Bypass |
|
OB-FW-CCB |
Bracket
for mounting one MX-60 |
|
OB-FW-CCB2 |
Bracket
for mounting two MX-60's |
|
OB-FW-CCB2-T |
Bracket
for 2 MX-60's on top of DC enclosures |
|
OBDC-60 |
60A
125VDC circuit breaker |
|
OBDC-70 |
70A
125VDC circuit breaker |
|
OBDC-175 |
175A
125VDC circuit breaker |
|
OBDC-250 |
250A
125VDC circuit breaker |
|
OB-FNDC |
Advanced DC monitor (Data
Sheet) |
|
OB-FW-SPACA |
FW-ACA
with surge protector (Data
Sheet) |
up to
the top |
