Battery Chargers

Features

• Over temperature protection
• Battery reverse polarity protection via fuse
• Output short circuit protection
• Up to 94% efficient
• IP22
• Can be used as a power supply
• Also charges Li-ion (LiFePO₄) batteries
• NIGHT and LOW setting
• Eleven LED’s for Status indication
• Storage Mode: less maintenance and aging when the battery is not in use
• Adaptive 6-stage charge algorithm: test - bulk – absorption - recondition – float – storage

The Blue Smart IP22 has built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.

Features

• Over temperature protection
• Battery reverse polarity protection via fuse
• Output short circuit protection
• Up to 95% efficient
• IP65 water, dust and chemical resistant
• Recovery of fully discharged ‘dead’ batteries
• Automatic compensation for high or low temperature
• Battery life enhancing features
• Can be used as a power supply
• Li-ion battery mode
• Low power mode to charge smaller batteries
• 7 step smart charge algorithm

Included

• Connect clamps
• M8 eyelet connectors

Optional accessories

• 12V cigarette lighter plug with fuse   
• 2 meter extention cable
• Connect clamps with fuse               
• M6 eyelet connector with fuse

Victron Blue Smart Chargers

These include all of the above features but in addition:

• Allows setup and configuration, with readout of voltage and current by Bluetooth Smart via smartphone.
• Status of the charger and battery and control of functions using the VictronConnect app. 

Perfect chargers for any type of battery Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail

Controlled charging Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes.

Use of TG Chargers as a power supply As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available.

• Microprocessor controlled three stage charging
• Models accept DC as well as AC input
• Can be used as a DC power supply
• 24V models feature additional 12V 4A isolated output to top up a starter battery
• Voltage & temperature sensors included for accurate charging
• 5 years warranty

The Skylla-IP44 (1+1) features 2 isolated outputs. The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.

• IP44 protection to withstands the rigours of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance.
• Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.
• LCD display. For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use.
• CAN bus interface (NMEA2000). To connect to a CAN bus network, to a Skylla-i Control panel or to the Color Control digital display. 
• Synchronised parallel operation. Several chargers can be connected in parallel and synchronised with help of the CAN bus interface. 
• The right amount of charge for a lead-acid battery: variable absorption time When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.

The Victron Skylla-i Control allows you to alter the charge current and see the system status of Victron Skylla battery chargers.

• Panel mount - can be surface mounted with optional wall mount enclosure

Phoenix Smart (3) adaptive 5-step chargers can provide charge to each of three battery banks or Phoenix (1+1) models have two outputs to provide 3A to the starter-battery, the rest to the ‘house’ bank. Bluetooth enabled to allow the charger to be monitored and alarms set straight from your phone.

Features

• Bluetooth Smart enabled. Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.
• Phoenix Smart (3): three full current outputs to charge 3 battery banks Each output can supply the full rated output current. But the total of the 3 outputs combined can never exceed the current rating of the charger.
• Phoenix Smart (1+1): two outputs to charge 2 battery banks. The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.
• Automatic voltage compensation. The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.
• Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage. The Phoenix Smart Charger features ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.
• The right amount of charge: variable absorption time. When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.
• Also charges Li-ion (LiFePO4) batteries. Charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.
• Fully programmable charge algorithm. The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three preprogrammed algorithms can be selected with the mode button (see specifications).
• Remote on-off. The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low.
• VE.Direct interface. For a wired data connection to a Colour Control panel, PC or other devices using the VictronConnect app.
• Programmable relay. Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events.

• AC Power Cord must be ordered separately.

The Victron Skylla-i is a modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.

• The right amount of charge for a lead-acid battery: variable absorption time.
• BatterySafe mode: preventing damage due to excessive gassing.
• Storage mode: less maintenance and aging when the battery is not in use.
• Smaller and lighter compared to similar models.
• NMEA2000 Canbus connection.
• PowerControl: set a maximum shore power.
• Remote Control.
• Li-ion (LiFePo4) ready.
• IP21 protection