Schletter Roof Mounting

The Universal Roof Hook is suitable for a wide variety of roofs and features: quality high-grade steel; variable bar arrangement; adjustable at the front and rear and the middle bar.

Rapid2+ for pitched roofs considerably reduces assembly time

• Rapid2+ versions include KlickTop attachment for quick and easy fitting of mounting rails
• All 4 mounting steps are carried out with only one tool (Torx TX40)
• Stainless steel
• Pre-assembled
• Universal versions enable batten size adjustment and vertical rail layout

The series HSL generation of roof hooks extends the broad portfolio of Schletter fastening elements for sloped tile roofs. Improved stability, innovative design, and fast, easy installation meet uncompromising efficiency and the utmost quality. The roof hooks consist of welded connections between the bracket and the screw-on mounting plate and are suitable for all common tile roofs with a wooden substructure.
Made of high-strength construction steel to meet all requirements for high stability and durability. 

Compared to roof hooks made of aluminum or stainless steel, fewer fastening points are required which makes system planning easier, shortens installation time, and reduces the PV system’s total costs.

• High-strength steel, welded
• Surface: premium-quality coating
• Bar arrangement: symmetrical
• Pre-assembled

The Rapid2+ includes KlickTop adapter and an EPDM rubber seal as a spacer.

The Schletter Roof Hook Rapid2+ Slate offers a simple reliable method for installing onto slate roofs.

• Aluminium roof hook and covering plate (ordered separately)
• Excludes wood screws
• Use 3x 6mm or 2x 8mm
• Screws in straight line for better narrow rafter suitability
• For slate overlappings up to 125 mm

Used for fastening mounting rails to corrugated roofs. Hanger bolt is screwed through the roof cladding and an adaptor plate bears the mounting rail. A UV-resistant EPDM sealing washer and collar are used to seal the drilled hole.

In the case of purlin roofs rails are usually mounted vertically and modules horrizontally on them.

Hanger bolt kit comprises:

• Hanger bolt
• Vulcanized EPDM seal (UV resistant)
• 3 x flange nuts 

The Schletter ClampFit Fastener is a simple and cost-efficient solution for mounting modules in landscape on trapezoial metal roofs with a minimum thikness of 0.5 mm.

• Less storage space required
• Quick to install
• Minimum trapezoidal beading height: 34mm
• Maximum trapezoidal pitch 45°

Module clamps to suit module frame thickness must be ordered separately

A fast and simple fastening system for self-supporting trapezoidal
sheet metal roofs for use with Solo5 rail

• Suitable for most trapezoidal steel sheet roofs from 0.5mm (0.02') thickness and aluminium sheet roofing from 0.8mm (0.03') thickness.
• No need to fasten to the roof substructure
• Panels can be mounted in portrait or landscape
• (landscape by clamping on the short edge)
• Quick to install
• Very little storage space required

Kit Comprises:

• 2 x SingleFix-V Solo fastening (for Solo mounting rails)
• 4 x self-tapping screws

A fast and simple fastening system for self-supporting trapezoidal 
sheet metal roofs

• Suitable for most trapezoidal steel sheet roofs from 0.5mm (0.02') thickness and aluminium sheet roofing from 0.8mm (0.03') thickness.
• No need to fasten to the roof substructure
• Panels can be mounted in portrait
• Quick to install
• Very little storage space required

Kit Comprises:

• 2x SingleFix-V Solo
• 4 self-tapping screws,
• Profile piece Solo 450 mm

For flat trapezoidal sheet roofs with less than a 10-degree slope, module installation parallel to the roof is not always optimal, due to low yields and inadequate module self-cleaning.

The FixZ system can be used for all common 60- to 72-cell framed modules to increase tilt angle giving an increase in tilt angles of between 5 and 7 degrees with FixZ-7, and 11 to 15 degrees with FixZ-15.

Pairs of Upper and Lower 450mm profiles are used, each in conjunction with a SingleFix-V Solo twin kit.

Aluminium module-bearing profile rails  - standard components of the fastening system. Solo05 for Klick system and compatible accessories.

Mounting with square nuts, Klick system and Rapid16 clamps.

• Top: Klick groove M8
• Bottom: Screw channel M10

Dimensions: 40mm w x 40mm h

Slide in connector allows rails to be joined together to extend length

.

Aluminium middle and end clamps for framed modules which allow quick and simple mounting by clicking into mounting rails and provide optimal holding force.

• Natural or black anodized aluminium
• Pre-assembled
• Includes Torx M8 screw with under-head serration and anti-friction coating
• All module clamps equipped with grounding pin

Used to allow horizontal mounting rails to be quickly & easily fastened to vertical rails.

 Comprises:

• KlickTop attachment with M8 bolt
• M8 square nut for Klick groove
• KlickIn click component for M8 nut

Wood screws for fixing Schletter roof hooks.

Designed especially for a safe fastening to corrugated fibre cement roofs on a steel substructure avoiding breakage and leaks.

Due to the utilisation of distance tubes, the fastening system FixE transfers fastening forces and possible bending moments safely into the substructure (such as sheet metal Z purlins). A specially shaped gasket made of UV-resistant EPDM-rubber serves as a sealing.

FixE fastening kits

Available as single or dual fastening kits including:

• aluminium top piece
• M8 stainless steel threaded screws with vulcanized EPDM-seal (UV-resistant)
• aluminium distance spacer tubes 

Screws, seals and top pieces also available separately.

Spacer also available in 1m lengths for cutting to size to suit different corrugated profile heights.

End caps and cable clips.