Victron Charge Controllers

These Victron Blue Solar Charge Controllers support a PV input with a maximum open circuit voltage of 75V or 100V respectively and have a maximum output of 20A. They work with and will automatically recognise 12V and 24V battery systems, except the VBS-MPPT100/20-48 which can be used with 12, 24 or 48V systems.

Highlights:

• Ultra fast Maximum Power Point Tracking (MPPT)
• 6 mm² screw terminals
• Up to 98% efficient
• Load output, connect ≤20A loads to be automatically disconnected/reconnected by the charge controller to stop the battery being over discharged
• ≤1A on 48V model
• BatteryLife: intelligent battery management algorithm, designed to increase the battery's life (see data sheet for details)
• Resin encapsulated electronics, added protection from the environment
• Automatic battery voltage recognition, no need to configure for 12V/24V systems
• 5 years warranty

These Victron Blue Solar Charge Controllers support a PV input with a maximum open circuit voltage of 100V and have a maximum output of 30A or 50A respectively. They work with and will automatically recognise 12V/24V battery systems.

Highlights:

• Ultra-fast Maximum Power Point Tracking (MPPT)
• 13 mm² screw terminals
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Over-temperature
• PV short circuit, reverse polarity and reverse current
• Internal temperature sensor, compensates absorption and float charge voltages
• 5 years warranty

This Victron Blue Solar Charge Controller supports a PV input with a maximum open circuit voltage of 150V and has a maximum output of 35A. It works with and will automatically recognise 12V, 24V and 48V battery systems (36V also possible via software configuration).

Highlights:

• Ultra-fast Maximum Power Point Tracking (MPPT)
• 13 mm² screw terminals
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Over-temperature
• PV short circuit, reverse polarity and reverse current
• Internal temperature sensor, compensates absorption and float charge voltages
• 5 years warranty

These Victron Blue Solar Charge Controller supports a PV input with a maximum open circuit voltage of 150V and have a maximum output of up to 100A. It works with and will automatically recognise 12V, 24V and 48V battery systems (36V also possible via software configuration).

Highlights:

• Bluetooth enabled (Bluetooth dongle needed)
• Ultra-fast Maximum Power Point Tracking (MPPT)
• Advanced Maximum Power Point Detection in case of partial shading conditions
• VE.Direct communication port
• Available with 35 mm² screw terminals (TR) or 3 sets of MC4 connectors (MC4)
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Over-temperature
• PV short circuit, reverse polarity and reverse current
• Internal temperature sensor, compensates absorption and float charge voltages
• 5 years warranty

These Victron SmartSolar Charge Controllers support a PV input with a maximum open circuit voltage of either 75V or 100V and have a maximum output of up to 20A. They work with and will automatically recognise 12V, 24V and 48V battery systems (48V with SmartSolar 100/20-48 only).

• Internal Bluetooth for wireless communication with smartphones or tablets.
• Ultra-fast Maximum Power Point Tracking (MPPT) for maximum energy harvest.
• Advanced Maximum Power Point Detection in case of partial shading conditions
• VE.Direct communication port
• Up to 98% efficient
• Load output, connect ≤20A loads to be automatically disconnected/reconnected by the charge controller to stop the battery being over discharged
• ≤1A on 48V model
• Electronic protection:
• Battery reverse polarity
• PV reverse polarity / Output short circuit / Over temperature
• Internal temperature sensor, compensates absorption and float charge voltages
• 6 mm² screw terminals
• 5 years warranty

These Victron SmartSolar Charge Controllers support a PV input with a maximum open circuit voltage of 100V and have a maximum output of up to 50A. They work with and will automatically recognise 12V and 24V battery systems.

• Internal Bluetooth for wireless communication with smartphones or tablets.
• Ultra-fast Maximum Power Point Tracking (MPPT) for maximum energy harvest.
• Advanced Maximum Power Point Detection in case of partial shading conditions
• VE.Direct communication port
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Battery reverse polarity (fuse, not user accessible)
• PV reverse polarity / Output short circuit / Over temperature
• Internal temperature sensor, compensates absorption and float charge voltages
• 16 mm² screw terminals
• 5 years warranty

This Victron SmartSolar Charge Controller supports a PV input with a maximum open circuit voltage of 150V and have a maximum output of up to 35A. They work with and will automatically recognise 12V, 24V and 48V battery systems (36V also possible via software configuration).

• Internal BlueTooth for wireless communication with smartphones or tablets.
• Ultra-fast Maximum Power Point Tracking (MPPT) for maximum energy harvest.
• Advanced Maximum Power Point Detection in case of partial shading conditions
• VE.Direct communication port
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Battery reverse polarity (fuse, not user accessible)
• PV reverse polarity / Output short circuit / Over temperature
• Internal temperature sensor, compensates absorption and float charge voltages
• 16 mm² screw terminals
• 5 years warranty

These Victron SmartSolar Charge Controllers support a PV input with a maximum open circuit voltage of 150V or 250V and have a maximum output of up to 70A. They work with and will automatically recognise 12V, 24V and 48V battery systems (36V also possible via software configuration).

• Optional display - plugs into front of controller for VSS-MPPT150/45 to VSS-MPPT250/70 units.
• Internal Bluetooth for wireless communication with smartphones or tablets.
• Ultra-fast Maximum Power Point Tracking (MPPT) for maximum energy harvest.
• Advanced Maximum Power Point Detection in case of partial shading conditions
• VE.Direct communication port
• Available with 35 mm² screw terminals (TR) or 3 sets of MC4 connectors (MC4)
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Battery reverse polarity (fuse, not user accessible)
• PV reverse polarity / Output short circuit / Over temperature
• Internal temperature sensor, compensates absorption and float charge voltages
• Remote on/off (2 pole connector)
• Programmable relay - DPST AC rating: 240VAC / 4A DC rating: 4A up to 35VDC, 1A up to 60VDC
• 5 years warranty

Identical to the SmartSolar Charge Controller MPPT but with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units.

When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device. 

• Optional display - plugs into front of controller for VSS-MPPT150/45 to VSS-MPPT250/70 units.
• Internal Bluetooth for wireless communication with smartphones or tablets.
• Ultra-fast Maximum Power Point Tracking (MPPT) for maximum energy harvest.
• Advanced Maximum Power Point Detection in case of partial shading conditions
• VE.Direct communication port and 2 VE.Can ports
• Available with 35 mm² screw terminals (TR) or 3 sets of MC4 connectors (MC4)
• Up to 98% efficient
• 8 preprogrammed algorithms selectable with a rotary switch
• Electronic protection:
• Battery reverse polarity (fuse, not user accessible)
• PV reverse polarity / Output short circuit / Over temperature
• Internal temperature sensor, compensates absorption and float charge voltages
• Remote on/off (2 pole connector)
• Programmable relay - DPST AC rating: 240VAC / 4A DC rating: 4A up to 35VDC, 1A up to 60VDC
• 5 years warranty

The MPPT RS SmartSolar is a 48V Solar charge controller with up to 450VDC PV input and either 100A, or 200A output. It is used in on-grid and off-grid solar applications where maximum battery  charging power is required.

• Multiple independent MPPT tracking inputs. With multiple MPPT trackers, you can optimise your solar panel design for maximum performance for your specific location.

• Isolated PV connections for additional safety. Full galvanic isolation between PV and battery connections provide additional overall system safety.

• Wide MPPT voltage range. 80 – 450 VDC PV operating range, with a 120VDC PV startup voltage.

• Light weight, efficient and quiet. Thanks to high frequency technology and a new design this powerful charger weighs only 7.9 kg for the 100A model. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation.

• Display and Bluetooth. The display reads battery, and controller parameters. The parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect.

• PV Isolation resistance monitoring.For peace of mind at higher voltages The MPPT RS continuously monitors the PV array and can detect if there are faults that reduce the isolation of the panels to unsafe levels.

• VE.Can and VE.Direct port. For connection to a GX device for system monitoring, data logging, and remote firmware updates. VE.Can allows for up to 25 units to be connected together in parallel and synchronise their charging.
• VSS-MPPTRS450/100-TR VE.Direct port not currently available for use with standard VE.Direct cables.

• I/O Connections. Programmable Relay, temperature sensor, auxiliary, digital input and voltage sensor connections. The remote input can accept the Victron smallBMS, and other BMS with allow-to-charge signal.

This Victron SmartSolar Control Display is a retrofittable LCD display for Victron's SmartSolar Charge Controllers. Simply remove the rubber seal that protects the plug on the front of the charge controller and plug-in the display.

Compatible with VSS-MPPT150/45 to VSS-MPPT250/100 units.

The Victron VE Direct Bluetooth Smart Dongle enables Victron MPPT Charge Controllers*, Battery Monitors* and Pheonix Inverters* to display information on IOS, Android, Windows or Mac OS X devices using the VictronConnect app.

• Monitor
• Configure
• Diagnose

*Compatible with all Victron products with a VE.Direct port, for full list of compatible products see the VictronConnect manual

The Victron MPPT Control enables you to setup and see the status off all Victron MPPT charge controllers that use a VE.Direct communications port.

Features

• View live status information
• Panel power
• Panel voltage
• Yield today
• Charger state
• Battery current
• Battery voltage
• Load output state
• Load current
• View historical information
• All-time values
• 30-day historical values
• MPPT charge controller setup

This Victron wall mount enclosure enables you to surface mount the Victron BMV battery monitor or MPPT Control charge controller display. Surface mounting makes installation much simpler and quicker rather than panel mounting where you need to recess the product.

V-MK3-USB interface allows conversion from VE Bus to USB for connection to a laptop and easy setup of inverter/chargers and other devices using Victron's VE Configure 3 software.

VE-DIR is used for comunication between a laptop and Victron VE.Direct devices

V-RS485-USB is used to communicate between the Victron energy meter and Victron Colour Control

• 5 years warranty

Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers to improve charging-efficiency and prolonging battery life.